Відео

Awesome!

So while hunting if I turn key on lights comes on thanks one question can I used that plug for hot wire to backup camera

Yeah, no its cool...not like i came here to figure out how to get the block in and aligned. Great vid...thx....

I was there

This will work. thx.

What was your tire size when you did this on all 4

Usually 3” drop coils you can fit in without compressing anything always . 1-2” coils need compressing. Like others said if you cut anything off an already made drop coil that’ has to have lowered the truck a ton more .. possibly conflicting with tire rub or clearance hopefully your front tires were still within range Next time use a GM spring compression tool the rentals work good . That bolt on the tool should have not snapped like that

Thank you for sharing! Now I know how to replace a emblem if I ever were to have to replace. Video helped much

Very good video. I bought my one owner SWB 112K mile 1998 Chevy C1500 W/T a couple of weeks ago. One of my first upgrades is to get the back of the truck level with the front. I bought the same shackles that you have. I was concerned about getting the top bolt out, but your plan was a good one. My truck may be a little more complicated as mine has a receiver hitch in the way. I will leave the bolts snug ( not tight) until the truck is on the ground and then tighten just a tad more. Did you have to get the truck frontend aligned again?

You complainin? Its a gift!

Nice! Got a lot done, block looks great so far

I advanced the timing on mine along with 3 sizes up piston and a new bore mine sounded a lot better than yours good to see tho

exactly the info I was looking for buddy. Thanks!

Can we get a truck update plz

wow man

Do you have any lifting kit installed??

If you take the foot part off the handle doesnt hold?! How you fixed that? Thanks

What’s the difference b/t neatsfoot and mink oil?

Fantastic! I’m about to get one. I think the willys has the wide axles from the max tow on the sport s?

Hey man I got a question

Hey man I hope you reply to this were did you get that nice chrome Shifter I’m replacing my transmission and would really like to buy a shifter like that

Looks like the wrong C-Notch🤔

How would it it bend it if the exhaust and gas tank higher?

Just what I needed to see! What is the difference between this and the Mojave other than the suspension and metal skid plate and I was told thousands of dollars cheaper? Thank You!

GOOD JOB MAN ..TANKS.FOR YOU VIDEOS...

Looks amazing!

I have a 4 speed stick shift. I just very slightly push down the emergency brake. Turns it off.

nice jeep homie g dog time to take the wife on a road trip 🤣

Does anyone know why he is afraid of the bike?

Muchas Felicidades Joven Por Su Canal. Saludos Cordiales Desde Mazatlán, Sinaloa, México. .. Que Precio $ Tiene Ese Kit? ??

I tell you what...I just did this install. Not too bad. But I put the bolts back in the way that makes sense so I won't have to go through that again.

What size tire is that?

Nice Job..! Awesome Work.! 👏🏼👏🏼👏🏼 You Should Slap some 50’s on the front with 60’s on the back with custom rims and low profile rubber..! That would of fit perfect with the one inch drop. 🤔 But still a very good job!👏🏼👏🏼👏🏼 “Peace”✌🏼😊👍🏼💯

How you survived this job is beyond me🤦🏾‍♂️🤦🏾‍♂️🤦🏾‍♂️ you have courage tho I’ll give you that.

Realizing I put it in inside out

Just got a hypertough 16 inch looks to be the exact same saw just rebadged

I noticed my old slave cylinder has a notch in it in which a clip was removed to disconnect the hose. The new slave cylinder does not have that notch, but has some sort of teeth inside which seems to grip the hose instead of a clip. Is this common and aftermarket parts or should I find a slave cylinder with the original clip? Thanks

looks like something from Walmart that was bought

Would pulling the starter make it an easier go, when removing the transmission. I'm looking at this job in the near future, Thanks for posting this.

Nice truck and nice toolbox

I have a 1998 GMC Sierra 2500 SL, and this is the only video I've seen that shows the style of clips it has for removing the airbag, I thought I was going crazy, the haynes manual was no help either. Thank you for making videos and putting that extra bit of info out there to help guys like me.

Torque specs? Hard to find.

Yo homie it’s the same shit for the GMC right ?

I hate this slave cylinder design lol just because it’s in the bell housing

Just setting up wood stove. When I look down the stove pipe hole there is a white material. Dost that white blanket stay in there? It's different from other wood stoves I have used.

If you have any questions regarding that classic 4.0 check out bleepinjeep. That guy has everything you need to know.

The good ole straight six ..

Yes, I have seen it on several of the 40 .0l i6s

Yea but before removing that theming chain is the cylinder you are working on at TDC?

Yeah, lots of forum posts about it. Some look really rough in comparison to yours, it's just from casting. Some look like a broken hole. Crazy pictures, do a little deep dive